Wasp WPL205 Bedienungsanleitung

WPL205 DIRECT THERMAL BAR CODE PRINTER USER’S MANUAL © 2007 Wasp Technologies

8 7. Thread the harness red connector through the cable hole at the front side of the lower inner cover. Plug the red peel-off module harness conn

9 3.4 Loading Label for Peel-off Mode (Option) 1. Open the peel-off module by pulling it out. 2. Thread the label, printing side facing up, thro

10 3.5 External Label Roll Mount Installation (Option) 1. Attach an external label roll mount on the bottom of the printer. 2. Install a roll of la

11 4. Power on Utilities There are six power-on utilities to set up and test printer hardware. These utilities are activated by pressing FEED butto

12 4.2 Gap/Black Mark Calibration, Self-test, Dump Mode While calibrating the gap/black mark sensor, the printer will measure the label length, print

13 Self-test The printer will print the printer configuration after gap/black mark sensor calibration. The self-test printout can be used to check if

14 Dump mode The printer will enter dump mode after printing printer configuration. In the dump mode, all characters will be printed in 2 columns as

15 4.3 Printer Initialization Printer initialization is used to clear DRAM and restore printer settings (with the exception of ribbon sensitivity) to

16 4.4 Black Mark Sensor Calibration Set black mark sensor as media sensor and calibrate the black mark sensor. Follow the steps below. 1. Turn off t

17 5. Maintenance 5.1 Cleaning Use one or more of the following supplies:  Cotton swab  Lint-free cloth  Vacuum  100% ethanol The cleanin

Table of Contents COPYRIGHT DECLARATION ...

18 6. Troubleshooting This section lists the common problems that you may encounter when operating the printer. 6.1 LED Status LED Status / Col

19 6.2 Print Quality Continuous feeding labels  The printer setting may go wrong. Please do the Initialization and Gap/Black Mark Calibration. No p

20 7. Specifications 7.1 Printer Specifications Item Specifications Mechanism Resolution Max. Print Width Max. Print Length Printing Speed Printing

21 Command Set WPL Environment Operation Temperature: 5℃ ~ 40℃. Relative Humidity: 25% ~ 85% (Non Condensing). Storage Temperature: -40℃ ~ 60℃. Re

22 8. LED and Button Operation 8.1 LED LED Color Description Green/ Solid This illuminates that the power is on and the device is ready to use. G

23 Gap/Black Mark Sensor Calibratio, Label Length Measurement, Self Test and enter Dump Mode 1.Turn off the power switch. 2. Hold on the butt

24 Gap Sensor Calibration 1. Turn off the power switch. 2. Hold on the button then turn on the power switch. 3. Release the button when LED turns r

1 Copyright Declaration Information in this subject to change without notice and does not represent a commitment on the part of Wasp Barcode Technolo

2 1. Introduction Thank you for purchasing the WASP WPL205 Direct Thermal Bar Code Printer. This printer provides both thermal transfer and direct

3 2.3 Printer Parts 2.3.1 Front View 2.3.2 Rear View 1 2 3 4 56 1. USB Interface 2. Centronics Interface 3. RS-232C DB-9 Interface 4. Power

4 3 Setup 3.1 Setting Up the Printer 1. Place the printer on a flat, secure surface. 2. Make sure the power switch is off. 3. Connect the printer

5 3.2 Loading Label Stock 1. Insert a 1” label spindle into a paper roll (If your paper core is 1 inch, remove the 1.5 inch core adapter from the fi

6 6. Close the printer top cover slowly and make sure the cover locks levers securely. Note: Failure to securely close and lock the cover will resul

7 3. Turn the printer upside down. 4. Unscrew the 2 screws in the lower inner cover. 5. Remove the screw at memory card cover. 6. Hold the